EXOTEK

TECHNICAL SPECIFICATION MC-380XCA INTENDED USERS Woodworkers, Cabinet and furniture makers Floor-ing installers, Contractors and quality assurance inspectors. Anyone who needs a professional quality tool to inspect wood and building materials for accurate moisture content or relative humidity. WOOD 230 different species of wood or user defined by density. BUILDING MATERIALS Ytong, Bricks, Wall tiles, Plaster, Eternit slab, Floor tiles, Sand, Sand stone, Lime stonePVC/Linoleum on concrete, Concrete, concrete slab, Clinker. MEASURING PRINCIPLE Capacitance type, non intrusive. Detection of dielectric changes due to variation of Moisture Content in the material using a High Frequency signal. MEASURING RANGE - CONCRETE Building material: 0- 98% Relative air Humidity (RH) MEASURING RANGE - MOISTURE CONTENT Wood (@ 200 kg/m3): 0- 85% H2OBuilding material: 0-15% H2O The Maximum value differs depending of the density of the material. MEASURING ACCURACY Approximately ± 1 % MC MEASURING GROUPS (DENSITY RANGE) 50 Wood Groups . (200-1180 kg/m3)19 Building Materials Groups. (1200-3000 kg/m3)SCANNING DEPTH (SELECTABLE) Internal sensor: Maximum 10 mm. 15 mm at high density materials.Measuring Springs: Maximum 100 mmAUTOMATIC SHUT DOWN Yes, 30 Seconds BATTERY WARNING Yes WORKING RANGE 0°C/+60°C DISPLAY LCD digital 3 ½ Digits RESOLUTION 0,1 % CASING ABS Plastic SENSORS Stainless Feather Steel Springs Built in. BATTERY 9 V alkaline, L6R22 CASE Artificial Leather SIZE (L x H x D ) 150 x 71 x 25 mm WEIGHT (INCL. BATTERY) 165 gram WARRANTY 2 years

EXOTEK MC-160SA PIN-FREE MOISTURE METER - RH FUNCTIONALITYDescriptionThe Exotek Instruments series is a new generation of microprocessor controlled, pocket size handheld moisture meters. For quick and accurate non-destructive determination of the moisture content in wood and building materials as well as locating wet areas in floors, roofs and walls made of homogeneous material. The MC-series includes different types of capacitance based moisture meters like theMC-60CPA, MC-380XCA and MC-160SA. It works on the principle of measuring the dielectric constant of the material. The field penetration depth is approximately 50 mm. It can be used under outdoor and indoor conditions. Choice of material code makes measurements more accurate. There are 10 selectable density groups for wood and 6 groups for building materials available. When making Bore hole Test's checking the Air Humidity, Relative Humidity (RH) is a more appropriate term. For this reason, the MC-160SA is programmed to calculate the RH value from the moisture content value (only for building material). FEATURES:Pin-less & non-destructive: Capacitance measurement using a high frequency dielectric fieldCould be used on different materials as wood, concrete, brick and plasterSelect from 6 wood groups (about 230 species) or 6 building material groups (E0 - E5)Moisture detection down to depth of 50 mmLow battery warning & Auto power offImpact resistant ABS housingComplete with 9V battery and carrying caseMC-160SA: 0 to 98% Relative humidity calculation for building materials @E1MC-160SA: 32 memory locations for average measurement storage in F4Indispensable for:WoodworkersCabinet and furniture makersFlooring installersContractors and quality assurance inspectorsAnyone who needs a professional quality tool to inspect wood and building materials for accurate moisture content or relative humidity. TECHNICAL SPECIFICATIONMC-160SAMEASURING RANGE-WOOD@ "200" kg/m³ 0-80 % H2OMEASURING RANGE-BUILDING MATERIAL@ "E1" 0-16 % H2ORH FOR BUILDING MATERIAL0-99% RHSCANNING DEPTH APPROX.50 mmHOLD FUNCTIONNoALARM FUNCTION (BUZZER)SettableAUTOMATIC SWITCH OFFYesLOW BATTERY WARNINGYesMEMORYYesOPERATING TEMPERATURE-10°C/+60°CDISPLAYLCD digitalRESOLUTION0,1%HOUSING MATERIALABSSENSOR TYPEStainless steel, electro polishedPOWER SUPPLY9V alkaline batteryCARRYING CASEArtificial leatherDIMENSIONS (h x w x d)150 x 71 x 25 mmWEIGHT (INCL: BATTERY)160gWARRANTY2 years 

MC-460 - Wood Moisture Meter - WOOD, TIMBER,SAWDUST,WOOD CHIPS The MC-460 is a digital hand-held moisture meter for quick and accurate determination of the moisture content in softwood, hardwood, other wood materials according to the resistance measuring procedure. Over 264 types of wood are registered in 6 measuring groups. Easy and clear operation, good reading off of indicated values, low power consumption, high, long-time stability without readjustment. NEW! Polarization function for fast and accurate reading when moisture content are higher than 15%. PROBES AND EQUIPMENTS-10 Double needle probe-woodS-10P Probe, 23 cm for paper and Palm Oil tree fibersS-30 Sliding hammer probeS-40 Compression Chamber Sampel Cup withConnection cable 1,0 mSurface electrodes, veneer measuringDurable plastic carrying caseSteel nail for S-10/S-30 probeLength and measuring depth: 12, 19, 26, 56 mmNeedle electrodes with Teflon isolation for S-10/S-30 probeLength and measuring depth: 30, 45 mm TECHNICAL SPECIFICATIONMC-460MEASURING RANGE - WOOD3–140% based on Dry weightMEASURING METHODElectronic resistor, invasiveWOOD GROUP COMPENSATION6/264 wood typesDISPLAYLCD digitalRESOLUTION0,1%TEMPERATURE COMPENSATION.Yes, in steps of 1.0 CelsiusSET SWITCH4LOW BATTERY CONTROLYesAUTOMATIC ELECTRONICALLY CALIBRATION DEVISEYesHOUSING MATERIALABSPOWER SUPPLY9V alkaline batteryDIMENSIONS (h x w x d)134x72x25 mmWEIGHT (INCL. BATTERY)160 gWARRANTY1 year 

MC-600SD Moisture Meter, Resistance type - MOISTURE METER FOR SAWDUST, HAY AND STRAWDescriptionSawdust Moisture Meter MC-600SD is a state-of-the-art device for measuring moisture contents in sawdust, wood shavings, slivers and other finely crumbled wood waste. It can also measure Moisture Content in Hay and Straw. The Moisture Meter measures the resistance of a compressed sample. The measurement is made in two stages: The sample is compressed to the pressure of approx. 0.2 MPa. The resistance of the sample is measured and converted into moisture contents.FEATURES:Fast display of measuring results.Indispensable for:Pellet (Pelletizing) and Brickette manufacturingAnyone who needs a professional quality tool to control Moisture Content in Sawdust, other wood shavings as well as Straw and Hay TECHNICAL SPECIFICATIONMC-600SDMEASURING RANGE MC-600SD-A SAWDUST,WOOD SHAVINGS8-50 H2OMEASURING RANGE MC-600SD-A HAY, STRAW10-30% H2O Relative Moisture ContentSAMPLE VOLUME120 cm3AUTOMATIC SWITCH OFFYesLOW BATTERY WARNINGYesOPERATING TEMPERATURE0 C/+50 CDISPLAYLCD digitalRESOLUTION0,1%ACCURACY8-15 %MC = +/- 1% Moisture Content16-28 % MC = +/- 2% Moisture ContentMEASURING METHODResistancePOWER SUPPLY9V alkaline batteryTRANSPORT CASEYesDIMENSIONS (h x w x d)300 x 215 x 65 mmWEIGHT (INCL: BATTERY)1 kgWARRANTY1 year 

WOOD AND TIMBERFMG 3000 - Moisture Meter for Wood ChipsThe moisture-meter FMG-3000 is designed to quickly determine the percentage of the moist content in wood chips. The moisture determines the heat value of the fuel and thus the price to which wood chips is accounted for. A moist content of about 40% in the wood chips halves the heat value. Conventional methods for the determination of the moisture are very time consuming. With FMG-3000 the moisture content in wood chips can be determined in a simple and quick way. Great importance was put on the user-friendliness handling. By simple keystroke, the percentage of the water content can be accurately read off on an LCD-display within seconds. The robust construction has been designed for heavy-duty use, for example in heating plants.   FINECOARSEMAX 20%Cross section cm2 = 3Length cm =8,5Mesh size mm =16Cross section cm2= 5 Length cm =12Mesh size mm        TTECHNICAL SPECIFICATIONFMG-3000Contains (Approx.)60 LitresMeasuring Range0-55% MoistureDIMENSIONS (H X W)640 X 500 MmWeight (Approx.)12 KgElectronic Controlled Battery Powered (Battery Charger Included)  

PAPER AND CARDBOARD  MC-60CPA  - Pin Free Paper Moisture DetectorThe MC-60CPA is a new generation of microprocessor controlled, pocket size handheld moisture meter. MC-60CPA is accurate, reliable and simple to use for rapid and non-destructive determination of the moisture content of paper and paperboard on rolls, stacks or reams. By pressing the sensor against the paper, the moisture content will be displayed within seconds. MC-60CPA can be used in production, inspection control and further treatment of paper materials. The choice of material code makes measurements more accurate. There are 5 selectable material codes for paper. FEATURES:Pin-less & non-destructive: Capacitance measurement using a high frequency dielectric fieldSelect from 12 material codes for paperMoisture detection down to depth of 50mm maxLow battery warning & Auto Power OffImpact resistant ABS housingComplete with 9V battery and carrying caseAPPLICATIONS:Filter Paper, tissue paperCrepe paperPackage paper, fluting paperKraft paperOffset paperCard BoardTECHNICAL SPECIFICATIONMC-60CPAMEASURING RANGE0-140% H2O @C2SCANNING DEPTH APPROX.50mm maxAUTOMATIC SWITCH OFFYesLOW BATTERY WARNINGYesOPERATING TEMPERATURE-10°C/+60°CDISPLAYLCD digitalRESOLUTION0,1%HOUSING MATERIALABSSENSOR TYPEChrome plated steelPOWER SUPPLY9V alkaline batteryPOWER CONSUMPTIONApprox. 5mACARRYING CASEArtificial leatherDIMENSIONS (h x w x d)132 x 62 x 30 mmWEIGHT (INCL. BATTERY)150gWARRANTY2 years 

OOD AND BUILDING MATERIALS MC-500 Low Cost Moisture Detector - Pin-freeThe MC-500 allows moisture detections in wood down to a depth of approx. 40 mm. It is designed for quick-response detection of moisture content in wood and building materials as well as locating wet areas in floors, roofs and walls made of homogeneous material. It is even able to detect moisture behind ceramic tiles or behind and under various floor or wall coverings. Simply place device on top of the surface to be examined – no injection into the object required!FEATURES:Pin-less & non-destructive: Capacitance measurement using a high frequency dielectric fieldCould be used on different materials as wood, concrete, cement wash floor, brick, plaster, gypsum board, clinker and clay floor tiles, sandstone, marble, etc.Quickly indicates the moisture content of materialsMoisture detection down to a depth of approx. 40 mmLow battery indicationImpact resistant ABS housingComplete with 9V batteryMC-500 can be used for:Detection of moisture in wood and other building materialsDetection of leakageFinding electrical cables and reinforcement bars TECHNICAL SPECIFICATIONMC-500MEASURING METHODDielectric constant measurementMEASURING RANGE-WOOD0–30% moisture contentMEASURING RANGE-BUILDING MATERIALdry/moist/wetSCANNING DEPTH APPROX.40 mmAUTOMATIC SWITCH OFFYesLOW BATTERY WARNINGYesOPERATING TEMPERATURE0 to +50°CDISPLAY3½-digit LCD-displayRESOLUTION0,1%HOUSING MATERIALABSSENSORBuilt in sensorPOWER SUPPLY9V alkaline batteryCARRYING CASEArtificial leatherDIMENSIONS (h x w x d)106 x 67 x 30 mmWEIGHT (INCL. BATTERY)150 gWARRANTY1 year 

WOOD AND BUILDING MATERIALSBDD "mini"- Low-Cost Moisture DetectorThe BDD “mini” is a pin-moisture detector used by Constructors, House inspectors, Woodworkers and Homeowners for rapid detection of moisture levels, moisture related problems, dampness and leaks in walls, floors and roofs.FEATURES:Detect dampness and related moisture problemsCheck surface moisture before painting, varnishing and other surface treatmentsLocate/trace source for leaks and dampnessTECHNICAL SPECIFICATIONBDD "MINI"MEASURING METHODElectronic resistorMEASURING RANGE-WOOD6-60% moisture contentMEASURING RANGE-BUILDING MATERIALdry/warning/wetLOW BATTERY WARNINGYesDISPLAY3½-digit LCD-displayRESOLUTION0,1%HOUSING MATERIALABSPOWER SUPPLY12V alkaline battery,8LR23, 1 pieceDIMENSIONS (h x w x d)75 x 38 x 15 mmWEIGHT (INCL. BATTERY)35gWARRANTY1 yearTECHNICAL SPECIFICATIONMC-500MEASURING METHODDielectric constant measurementMEASURING RANGE-WOOD0–30% moisture contentMEASURING RANGE-BUILDING MATERIALdry/moist/wetSCANNING DEPTH APPROX.40 mmAUTOMATIC SWITCH OFFYesLOW BATTERY WARNINGYesOPERATING TEMPERATURE0 to +50°CDISPLAY3½-digit LCD-displayRESOLUTION0,1%HOUSING MATERIALABSSENSORBuilt in sensorPOWER SUPPLY9V alkaline batteryCARRYING CASEArtificial leatherDIMENSIONS (h x w x d)106 x 67 x 30 mmWEIGHT (INCL. BATTERY)150 gWARRANTY1 year 

WIND METER / THERMO ANEMOMETERExotek WM01 Thermo Anemometer - Air Velocity and Temperature MeterThe WM01 Thermo-Anemometer could due to its small and compact design be used as a pocket weather meter. Display the air velocity and temperature or temperature and wind-chill factor.FEATURES:Pocket-knife design makes it convenient and portableTemperature/wind-chill: Average updates every secondWind speed: Moving 2-second average with maximum 2-second gustMeasurement units: Knots, Mph, Km/h, ft/min, m/s, BeaufortAverage readings 5 / 10 / 13 second averagesSealed precision thermistorRecords maximum readings?C / ?F unit switchableAuto power off: Approx. 20 min.Replaceable lithium battery?Data Hold? freezes the readingTECHNICAL SPECIFICATIONWM01MEASURING RANGE - TEMP-18 to +50?CMEASURING RANGE - WIND0,8 to 72 km/h (0,2 to 20 m/s)ACCURACY+/- 1?COPERATING TEMPERATURE-15 +50?CDIMENSIONS-180? Fully opened (l x w x t)235 x 45 x 25mmDIMENSIONS Folded (l x w x t)140 x 45 x 25mmUNIT SELECTABLE (?C/?F)YesDISPLAY HOLDYes  

COATING THICKNESS METERS - Easy-Check FNDescriptionThickness meter with a swinging probe for measuring on ferrous and non-ferrous metals. Conforms to ISO2360:2003.The newly developed measuring probe is integrated in the meter and can swing by 90° i.e. the meter can be set in a vertical position or by swinging the probe head round it is possible to measure inside pipes or in other nearly inaccessible places. An outstanding feature of this probe is that a calibration down to a material diameter of 5 mm is no longer necessary on steel. Easy-Check FN is equipped with a data logger for 100 readings and has a serial interface RS 232 C. The instrument is supplied with a calibration kit (plates and shims) and a leather case with belt loop.Specification TECHNICAL SPECIFICATIONEASY-CHECK FNMEASURING RANGE0-5000 microns-on iron and steel0-2000 microns-on non-ferrous metals0.1 microns at 0-100 micronsACCURACY± 1% at 100-1000 micronsSIZE108 x 48 x 38 mmPOWER SUPPLYHybrid battery 6.2 VWEIGHT100 g