FIELDPIECE

Fieldpiece JL3KH6 Job Link Probes Charge and Air KitWireless range of 350' plusDirectly connects to mobile device with Job Link System AppFast accurate temps with new Rapid Rail technologyPressures auto calibrate at any elevationConfigurable psychrometers with flexible probe and sliding magnetGeneral SpecificationsWireless Range350 feet or moreWireless Frequency2.4 GHzBattery2 x AAA (included)Battery Life150 hrs typical alkalineAuto Power Off (APO)2 hrs (can be disabled)Minimum Device RequirementBLE 4.0 devices running iOS® 7.0 or Android 5.0Job Link Pressure Probe - JL3PRConnector Type45° Standard 1/4" NPT female flareBest Accuracy±1 psig (±7 kPa)Measurement Range0 to 580 psig (0 to 4000 kPa)Maximum Overload800 psig (5500 kPa)Water ResistantDesigned to IP55Job Link Premium Pipe Clamp Probe - JL3PCPipe CompatibilityElectrically conductive 1/4" to 1 3/8" (6.4mm to 34.9mm) dia.Accuracy±1°F (±0.6°C)Measurement Range-50°F to 257°F (-46°C to 125°C)Stabilization Time3 seconds typicalMeasurement FeedbackBeeper and LEDWater ResistantDesigned to IP55PatentPendingJob Link Flex Psychrometer Probe - JL3RHFlexible Probe0.36" (9mm) diameter, 9.25" (235mm) lengthBest Accuracy±1°F (±0.6°C) ±2.5 %RHMeasurement Range-4°F to 140°F (-20°C to 60°C) 0 %RH to 100 %RHMultimeter

Fieldpiece SRS1 - Residential, Light Commercial Refrigerant ScaleScale up to 110 lbs110 lb capacity0.25 oz (0.01 kg) resolutionNumeric keypad for easy operationLarge LED screen, easy to see from a distanceWeight alarm for charging and recoveryLightweight and easy to carrySturdy aluminum constructionWater resistant SpecificationsGood in ambient conditions of73°F ±9°F (23°C ±5°C), <75% relative humidityOver range"OL" is displayed and beep soundsMaximum load110 lbs (50kg)Auto power off30 minutes of inactivity (no change in weight or buttons pressed), (APO disabled in charge/recover mode)BacklightBlue, turns off in 60 seconds if no buttons are pressedAccuracy±(0.05%rdg + 10g)Resolution and UnitsLB OZ (1 LB, 0.25 OZ), LB (0.02 LB), OZ (0.25 OZ), KG (0.01 KG)Temperature coeffcient0.1 x (speciffed accuracy) per °FBattery9V, NEDA 1604, JIS 006P, IEC 6F22Battery life80 hours typical alkaline (without backlight)Low battery indication is displayed when the battery voltage drops below the operating levelOperating environment32°F to 122°F (0°C to 50°C) at <75% RHStorage temperature-4°F to 140°F (-20°C to 60°C), 0 to 80% RH (with battery removed)Weight6.6 lbs (3.00 kg) Alat Laboratorium Umum

Fieldpiece MR45 Digital Recovery MachineFieldpiece MR45Protects from voltage drop (runs as low as 95 VAC)Extra large condenser cools faster, especially on hot daysSingle dial self purgeOnly 22 lbsWater resistance to withstand direct rainThe Fieldpiece MR45 recovery machine has onboard system monitoring that adjusts motor performance to handle liquid and run twice as fast on vapor. MR45 also steps up low voltage at the power plug to deliver full power to the motor where high voltage drop is a problem. With a powerful 1HP motor and super-sized condenser, this machine excels on longer and hotter jobs. The easy-to-read display, lightweight (22lbs), straight hose connection ports, and single dial make this machine user-friendly while being tough enough for everyday use, even in the rain.In The BoxMR45 Refrigerant Recovery Machine3 Extra Mesh Screens for Input Port1 Extra O-ring for Input PortOperator’s Manual1 Year Warranty Manufacturer SpecsDisplay2 x 10000 count LCD with status messagesBacklightBlue colorMeasurement rate3.3 times per second, nominalInput Port Pressure Sensor Range-30" Hg to 600 psigOutput Port Pressure Sensor Range-30" Hg to 600 psigHigh Pressure Cutoff558 psig, nominalResolution and Units1 psig (1" Hg), 0.05 bar (2 cmHg), 0.01 Mpa (2 cmHg), 5 Kpa (2 cmHg)Pressure Sensor Accuracy± 0.5" Hg (Vacuum), ± (0.6% of reading +2 psig)Final Recovery Vacuum14.9" HgCompressorTwin cylinder reciprocating (oil-less)DC Motor1 HP (variable smart speed)Power Source95 to 130 VAC @ 60 Hz 1 phaseMax Current Draw12.0 AACValveSingle dual-route ball valveInput Port Filtration11 mm mesh screen, stainlessDimensions14.8" x 9.8" x 13.5" (376 mm x 250 mm x 344 mm)Weight22 lbsOperating Environment32°F to 122°F (0°C to 50°C)Storage Environment-4°F to 140°F (-20°C to 60°C)Approved RefrigerantsR12, R134A, R22, R401A (MP39), R401B, R401C, R402A, R402B, R404A, R406A, R407A, R407B, R407C, R407D, R408A, R409A, R410A, R411A, R411B, R412A, R500, R502, R507, R509.Alat Ukur Lainnya

Fieldpiece ST4 Dual-Temperature MeterDescriptionThe Fieldpiece Dual-Temperature Meter, model ST4, measures two temperatures simultaneously using the included k-type, wrap tab beaded thermocouples. The technology inside the ST4 provides superior temperature compensation in rapidly changing environments commonly found while performing field service. Use the ST4 to find Delta T and just about any temperature split you want to measure. Displays T1, T2 and T1-T2 in big numbers on the LCD screen. Features two front face calibration pots and comes in our clear front case with magnetic hanger model ANC6. Use with our optional ATWB1 wet bulb thermocouple to help you find target superheat or with our pipe clamp T/Cs to check for blocked dryer filters.How Does it Work? Plug in one or two of the supplied k-type thermocouples and find T1, T2, or T1-T2. The ST4 has been designed to be used while inside the carrying case. Use the magnet to hang it. The front is clear so you can press the buttons and read the display. The zippers allow the thermocouples to exit from the top of the case.Operation.Turn on the ST4.Select ºC or ºF.Plug in one or both of the k-type thermocouples to the top of the ST4. The red LED will light up when a necessary thermocouple isn’t engaged.Press “T1” for the left thermocouple. Press “T2” for the right thermocouple. Press “T1-T2” to get the real-time difference between the two thermocouple readings.Select temperature resolution by pressing the “1º/0.1º” button.“HOLD” keeps current reading on screen until “HOLD” is pressed again.Press once to record MIN and MAX. Press once to toggle between MIN and MAX. Hold down for 1 second to exit the MIN/MAX function.Operate the ST4 in it’s case to take advantage of the hanger. You can operate the ST4 while still in the carrying case because of the clear front window.Note: When in HOLD or MIN/MAX, you cannot change ºC/ºF or resolution (1º/0.1º). Manufacturer SpecsGeneral SpecificationsMeasurement range-58ºF to 2000ºF (-50ºC to 1300ºC)Resolution0.1ºTemperature coefficient0.1 x (specified accuracy) per °C (0°C to 18°C, 28°C to 50°C)System accuracy after field calibration±1ºF @ 30ºF to 120ºF with field calibration±0.5ºC @ 0ºC to 50ºC with field calibrationMeter accuracy  Accuracies for any of the given ranges below are specified for operating temperatures between 64ºF to 82ºF (18ºC to 28ºC), for 1 year, not including thermocouple error. ±4ºF @ -58ºF to 32ºF±(0.3% rdg + 2ºF) @ 32ºF to 1100ºF±(0.5% rdg + 2ºF) @ 1100ºF to 2000ºF±2ºC @ -50ºC to 0ºC±(0.3% rdg + 1ºF) @ -50ºC to 600ºC±(0.5% rdg + 1ºF) @ 600ºC to 1300ºCMeasurement rate2.5 readings/second.BatterySingle standard 9-volt battery, NEDA 1604, JIS 006P, IEC 6F22.Battery life100 hours- carbon zinc battery. 200 hours- alkaline battery. Replace when "battery icon" is displayed.Operating environment32ºF to 122ºF <70% RH.Storage environment-8ºF to 140ºF <80% RH with battery removed from meter.Display3.5 digits LCD, 2000 count.Overrange“OL” or “-OL” is displayed.Accessories9V battery (installed), 2 k-type thermocouples, 2 Velcro straps, rubber boot, case, and operator’s manual.SafetyDesigned to meet IEC-1010-1, CE-EMC.Alat Laboratorium Umum

Fieldpiece SDMN5 Dual Port ManometerPortable, rugged dual-port manometerUsed to check gas pressure, static pressure and pressure differentialMeasures pressure between -60inWC and 60inWC, and -150.0 to 150.0 mBarThe Fieldpiece SDMN5 is a portable, rugged dual-port manometer designed to measure gas pressure, static pressure and pressure differential. Its range and resolution allow you to measure the applications you run into everyday in HVAC/R field service. Measure gas pressure on the inlet and outlets with the standard 3/16" fittings or the included adapters for 5/16" ports, take static pressure measurements across a blower and get the pressure differential with the push of a button to check drafts. Whether you’re holding the ergonomic standalone shape in your hand or hanging the SDMN5 on the unit with the magnetic hanger, the SDMN5 makes HVAC/R field service easier and faster, with less fatigue than the other guys.The SDMN5 includes a zero adjust button of the face of the meter, a rugged rubber boot, a magnet on the back for hanging the meter, and Auto Power-Off (APO) for conserving battery life. The SDMN5 measures pressure between -60inWC and 60inWC or -150.0 to 150.0 mBar. It can measure P1 or P2 pressure readings, as well as calculate the difference between them, and static pressure measurements can be made with a resolution of 0.01inWC or 0.01mBar. The Fieldpiece SDMN5 also includes a 3/16" to 5/16" SpecificationGeneral SpecificationsAccuracyStated accuracy at 0 to 50°C (32 to 122°F): ±1.5% FSBatterySingle standard 9-volt battery, NEDA 1604, JIS 006P, IEC 6F22Battery Life200 hours with low battery indicator on displayOperating environment32ºF (0°C) to 122ºF (50°C)Compatible MediaDry, non-corrosive gasesOverrange"OL" or "-OL" is displayed.Auto-Off power15 minutesLow Batterysymbol is displayedDimensions180mm(~7 1/16")(H) x 60mm(~2 3/8")(W) x 30mm(~1 3/16")(D)Weightapproximately 195g including batteryPressurePressure Portstube connectors for 5mm (~3/16 inch) I.D. flexible tubingUnits of MeasureinWC, mmWC, mbar, PSIResolution0.01 inch WCAccuracy/RangesinWC: ±0.02 on 0.00 to ±2.00±1.5% FS on 2.00 to ±60.0mmWC: ±0.5 on 0.00 to ±51.0±1.5% FS on 51.0 to ±1500mbar: ±0.05 on 0.00 to ±5.00±1.5% FS on 5.00 to ±150.0psi: ±0.001 on 0.000 to ±0.07±1.5% FS on 0.07 to ±2.000Alat Laboratorium Umum  Alat Laboratorium Umum

Fieldpiece SDMN6 Dual Port Manometer and Pressure Switch TesterDual port manometerGas pressure up to 60" WC with resolution of 0.1" WCStatic pressure up to 2"WC with resolution of 0.010"WCMeasures both positive and negative pressureTests pressure switches by simulating draft with an internal pumpCalibrate adjustable pressure switches to specificationThe Fieldpiece SDMN6 dual-port manometer measures gas and static pressure and also accurately tests pressure switches by simulating a draft with an internal pump. A pressure switch is a safety device that prevents a furnace from running in an unsafe manner. The SDMN6 tests the pressure switch to determine if it is working properly, or if it is starting to fail which can cause the furnace to run in an unsafe manner. Plus, with the SDMN6 you can easily calibrate any adjustable pressure switch to manufacturers' specification, so there's no need to carry a large variety of pressure switches on your truck.The Dual Port Manometer has the ranges to measure gas pressure and the resolution needed to measure static pressure. Ideal for HVACR field service technicians, the SDMN6 can determine if the gas pressure coming into the house or out of the regulator are correct. The SDMN6 measures gas pressure up to 60" water column (WC) with a resolution of 0.1" WC. In addition, the unit measures both positive and negative pressure, which is used for measurement on vacuum control lines. The unit will take differential pressure readings and display the difference between P1 and P2 at all times in the lower right corner of the easy-to-read LCD. Four different measurement scales can be used: inches of water column, millimeters of water column, mBar, and PSI.The SDMN6 also has a zero adjust to zero out the meter in different ambient pressures. It has a hold button to hold the currently displayed reading. The auto-power-off function conserves battery life, but can be disabled if desired. In the static pressure mode, the unit can measure up to 2"WC with resolution to 0.010"WC, which enables a technician to measure small differences in air (or static) pressure.Manufacturer SpecsSpecificationsOperating environment32°F to 118°F (0°C to 48°C) at <80% RHStorage temperature-4°F to 140°F (-20°C to 60°C), 0 to 80% RH (with battery removed)Power9V, NEDA 1604A, IEC 6LR61 9V alkaline battery.Battery life (alkaline)200 hours (manometer only, backlight off), 12 hours (pressure switch testing @ 27% pump speed, BL off, approx -2.5"WC induced pressure w/o pump bleed accessory)Auto power off (APO)15 minutesLow battery indicationsymbol is displayedUnits of MeasureinWC, mmWC, mbar, psiResolution0.01 inWCOverrange"OL" or "-OL" is displayedMax Pressure900inWC (17.4psi) will damage sensorsCompatible mediaDry, non-corrosive gasesPressure ports2 connectors (P1, P2) for flexible tubing (4.5mm to 8mm ID)Pump port1 connector (PUMP) for 5mm (~3/16 inch) ID flexible tubingLead jacks2 banana plug jacks for testing open/close switch status (continuity between terminals)AccuracyStated accuracy at 0 to 50°C (32 to122°F): ±1.5% FSAccuracy and rangesinWC: ±0.02 on 0.00 to ±2.00 (±1.5% FS on 2.00 to ±60.0)mmWC: ±0.5 on 0.00 to ±51.0 (±1.5% FS on 51.0 to ±1500)mbar: ±0.05 on 0.00 to ±5.00 (±1.5% FS on 5.00 to ±150.0)psi: ±0.001 on 0.000 to ±0.07 (±1.5% FS on 0.07 to ±2.000)Alat Laboratorium Umum

Fieldpiece SOX3 Combustion Checker with Auto PumpCombustion CheckerFast, Easy Furnace TuningMeasures flue temp and %O2Calculates %CO2, %EA, and combustion efficiencyHands-free testing with magnet, R-cone, and automatic pumpProgrammable for custom fuel typesManufacturer SpecsSensor TypeHighly accurate oxygen sensor.Operating environment32 to 122°F (0 to 50°C) at <75% R.H.Storage environment-4 to 140°F (-20 to 60°C) at <80% R.H. with battery removed from meter.Temperature Coefficient0.1 times the applicable accuracy per ± from 32°F to 64°F and 82°F to 122°F (0 to 18°C and 28 to 50°C)Battery Life28 hours typical alkaline.Auto Power offAfter 15 minutes.AccuracyStated accuracy at 23°C±5°C, <75% R.H.Display4 digit liquid crystal display(LCD) with maximum reading of 9999.TemperatureRange-58°F to 1000°F (-50°C to 538°C)Resolution0.1±Accuracy±[0.6%+3°F(1.7°C)]after field calibration.Sensor TypeRod K-type thermocouple.Range50°F to 900°F (continuous operation range)up to 1000°F (single exposure use)Accuracy(±4°F) on -50°F to 545°F (±0.75%) on 545°F to 1000°FOxygenOxygen Range0 to 25%Accuracy±0.3%O2(Calibrated at 72°F, 20.9%O2)Max Overload30% OxygenOperational temp range-4°F to 122°FResponse timeUnder 2 minutesAlat Ukur Lainnya

Fieldpiece VP85 - 8 CFM Vacuum Pump8 CFM, two stage vacuum pump4 Inline Ports - 1/4", 3/8" (x2), 1/2"RunQuick Oil Change SystemOn the fly oil change in secondsBacklit oil reservoir to view condition of oil and systemSturdy base to stay uprightSimple-to-use gas ballast with LED indicatorWater resistant to withstand direct rain15 micron ultimate vacuumAnti oil-suck-back keeps oil out of gauges and system Manufacturer SpecsSpecificationsFlow Rate8CFM (VP85), 5CFM (VP55)Oil Capacity8oz (237mL)Oil CompatibilityFieldpiece Vacuum Pump Oil (Highly refined and optimized for proper sealing and lubrication)Oil BacklightBlue LEDOil DrainBall valvePort Sizes(1) 1/4", (2) 3/8", (1) 1/2"CompressorRotary vane, two stageMotor3/4 HP Brushless DC (VP85), 1/3 HP AC (VP55)RPM2500 (VP85), 3440 (VP55)Power Source95 to 130 VAC @ 60 Hz (VP85) 108 to 130 VAC @ 60 Hz (VP55)Nominal Current Draw9.0 AAC (VP85), 8.0 AAC (VP55)Ultimate Vacuum at Input Ports15 micronsDimensions9.25" x 12.4" x 17.7" (235 mm x 315 mm x 450 mm)Weight28 lbs without oil (VP85), 30 lbs without oil (VP55)Operating Environment30°F to 122°F (-1.1°C to 50°C) In The BoxVP85 Vacuum Pump(2) 8 Ounce Vacuum Pump OilOperator's ManualAlat Laboratorium Umum

Fieldpiece AAV3 Air Velocity and Temperature Accessory HeadAir velocity and temperature accessory headEasy to use vane anemometerEstimate CFMLarge vane covers most of register's free areaDisplays average measurement and real-timeHow to useConnect to COM and Volts jack. Slide AAV3 air velocity and temperature accessory head onto Fieldpiece "stick" meter, data logger, electronic handle or connect to most other meters using Fieldpiece ADLS2 deluxe test leads.Set meter to 200mVDC or 2000mVDC range.Power on the AAV3 and select English or metric along with desired unit of measure.Select display mode. Average shows a steady, average of the last 16 seconds of readings. Real time shows every reading and will change immediately if there is a change in air velocity. (Note: temperature readings are always in real time regardless of the setting.)If the green “LCD x 100” LED lights up on the AAV3, you must multiply the LCD reading by 100 to get the true value.Manufacturer SpecsGENERALOperating temperature32 to 120 ºFResolution±0.1ºFOperating relative humidity<95%RHStorage temperature-4ºF to 140ºF, 0 to 80% R.H. with battery removed from meter.Sensor typeThermistor temperature sensorBattery life200 hours typical. No measurable current draw when in "off" position.Low battery indicationRed LEDBattery9VAuto offApprox. 10 minutes.Conversion1mVDC/unit of measure except FPM >2000. At >2000FPM the green light lights up and conversion rate changes to 1mVDC/100FPM (multiply LCDX100).Output1mV/unit of measure (1mV/100ft/min above 2000 fpm). AIR VELOCITYRange60-5900 Ft/min, 0.7-67.0 mph, 0.3-30.0 M/s, 1-108 KM/hrAccuracy±3% + 1digit @73ºF±5ºF, <95% relative humidityUnitsFft/min, meters/sec, MPH, KM/hr TEMPERATURERange-20ºC to 60ºC, -4ºF to 140ºFAccuracy±0.5ºC at 0ºC to 45ºC;±1ºC at -20ºC to 0ºC, 45ºC to 60ºC;±1ºF at 32ºF to 113ºF;±2ºF at -4ºF to 32ºF, 113ºF to 140ºFUnitsDisplays ºF and ºCIn The BoxAir Velocity and Temperature Accessory - AAV39V Alkaline Battery (installed)Operators manualAnemometer

Fieldpiece STA2 In-Duct Hot-wire AnemometerMeasures air velocity and temperatureCalculates CFMSlim 38" telescoping probe for in duct traversingFast response timeDual display for combo of real-time CFM, air velocity, or tempDepth and direction indicatorsMinimizes turbulence effect with time/test point averagesHands-free testing with stabilizing cone and magnetic hangerManufacturer SpecsTemperatureSensor typePrecision thermistorRange-4°F to 140°F (-20°C to 60°C)Resolution0.1°F / 0.1°CAccuracy±(1°F) 32°F to 113°F±2.0°F for -4°F to 32°F, 113°F to 140°F±0.5°C for 0°C to 45°C±1.0°C for -20°C to 0°C, 45°C to 60°CVelocitySensor TypeMicro-glass bead thermistorResolution1 fpm (0.01 m/s)Range40-3960 fpm (0.20-20.00 m/s)Accuracy± (5%+1 dgt) reading or ± (1%+1dgt) full scaleUnitsfpm, m/s, km/hr, mphAccuracyStated accuracy @ 73°F±9°F (23°C±5°C), <90%RHTemperature coefficient0.1 x (specified accuracy) per °C for 0°C to 18°C, 28°C to 50°C (32°F to 64°F, 82°F to 122°F)Operating environment-4°F to 122°F (-20°C to 50°C) at <75%RHStorage temperature-4°F to 140°F (-20°C to 60°C), 0 to 80% RH (with battery removed)Temperature Coefficient0.1 x (specified accuracy)/°C (28°C)Over range"OL" or "-OL" is displayedPowerSingle standard 9-volt battery, NEDA 1604, JIS 006P, IEC 6F22Battery9VBattery life20-35 hours approx. (alkaline)Auto Shut off15 minutes of inactivity (switchable)Dimensions7.2 in (H) x 2.5 in (W) x 1.3 in (D) [185mm (H) x 65mm (W) x 35mm (D)]Weight12 oz. (340g) including battery In The BoxStabilizing coneBlow-molded case with paddingAnemometer